by Dean Dean

How To Replace Honda GX690 Fuse

How To Replace Honda GX690 Fuse

Are trying to figure out How To Replace Honda GX690 Fuse?  If so, this video post is perfect for you!  I’m Doug Rucker and my passion is helping pressure washing business pros start and grow their business.  In addition to my commercial power wash service in Houston, I also provide training and equipment.  Sometimes, the Honda GX690 won’t start.  This video post is the result of a question from one of our viewers asking for more details from an earlier video.  We sure hope this video about How To Replace Honda GX690 Fuse helps if you experience this issue.

SMALL FUSE

It’s really amazing that something so small as a fuse can stop work on a job and ruin your day.  But these are the kinds of thinks we like to prepare you for.  It’s just a small 30 amp fuse, and it’s hidden from view behind the key switch.  I have experienced with this first hand both with a cold start and even when trying to restart on a job after turning it off.  The usual first assumption is a dead battery but it’s important to consider the fuse first.  So for How To Replace Honda GX690 Fuse, you’ll need a 10 mm socket.  There are two screws behind the key switch to remove.  One is on top and the other is right beneath it.  This will detach the key switch box from the engine.  At the 5:15 time stamp, you’ll see one phillips-head screw that you also need to remove. You then remove a wire harness band which looks like a big o-ring.

FUSE HOLDER

There is a small case or fuse holder that you can access.  At this point, pull the 30 amp fuse out and replace it with a new 30 amp fuse.  Then check to see if starting is successful.  I also suggest leaving the fuse holder hanging outside for easy access if this occurs again.  And of course, keep spare fuses with you on hand somewhere with your rig.  This way, you won’t lose any time on the job due to such a small and easy maintenance fix.  Be sure and watch the entire video for all the little tricks and details I provide.  And leave a comment if you have experienced this issue and if this video post was helpful in resolving it.

 

 

by Dean Dean

CHECK VALVE REPAIR

CHECK VALVE REPAIR

This 2023 CHECK VALVE REPAIR video post features the repair kit for downstream injector check valves.  Recently, email and text message questions came in regarding how to repair them rather than replacing them to save a few dollars.  Later in this video, I go into further detail about how use them, why we use them and when to use them.  I also cover installation steps.  We hope this CHECK VALVE REPAIR video helps you in your day to day pressure washing business.  Our business is to help your business save time, money, and effort so that you can maximize profitability.

REPAIR INSTRUCTIONS

It’s important to take note of the small arrow which indicates the way the water flows.  But it also points to the side which you’ll need to release with a vice and pliers to start the repair steps.  As you loosen this piece, be ready for the spring and check valve itself to fall out.  Notice the precise order so you can put them back in correctly.  Then you would use a dental pick to left the small o-ring from its seating inside.  You are simply installing the new spring and 0-ring into the existing case or housing piece.  At the 4:15 time stamp, I demonstrate how to blow through it for the purpose of diagnosing CHECK VALVE REPAIR problem issues.  Once again, our line of High Performance oils comes in handy.  The lubricant spray will help unseat challenging o-rings if you have problems trying to remove them.  6:15 is a critical time stamp spot you don’t want to miss.

 

INSTRUCTIONS FOR USING

At approximately 9:00, I transition from repair to the ins and outs of using them.  I talk in detail about installing and using the downstream injector check valve setup.  These are available on our Doug Rucker Store website in a couple of difference types or configurations.  There is also an option of RTU, which means ready to use.  The DIY option means you will assemble it yourself and save a few dollars that way.  Be sure and watch the entire video to get the full impact and information you need for your pressure washing business.  Finally, I want to invite you to one of our monthly hands on trainings here in the Houston area.   It’s a great way to get equipment orientation with classroom learning.  It will drastically reduce your learning curve!

 

by Dean Dean

PRESSURE WASHER FITTINGS

PRESSURE WASHER FITTINGS

This PRESSURE WASHER FITTINGS video addresses an option you have as it relates to fittings.  That option is either socket in/plug out OR plug in/socket out.  This question arises from customers ordering equipment from us such as modified xjet, pressure wash gun assembly, and even downstream injectors.  This can get somewhat complicated so I like to try and simplify it as best as I can for those who are new in the business.  It’s basically the orientation of or how to set up your inlet and outlet fittings.  I hope this PRESSURE WASHER FITTINGS video helps clear up some of the confusion.

MY FITTINGS PREFERENCE

My preference has always been to set up my system PLUG OUT.  Early in my training years when I first stared in the business, I was taught that “the plug points the way the water flows.”  So for my ball valve set up, the water is coming into valve through the socket.  This might also be called a coupler or the female fitting.  Then the water flows out from the ball valve through the plug.  So my PRESSURE WASHER FITTINGS set up or orientation is PLUG OUT.  So this set up applies to all equipment.  This set up can easily be reversed for a variety of reasons.  But, either way, it must remain consistent throughout the entire system.  At approximately 2:50 into the video, I demonstrate the importance of water flow direction on a downstream injector.  There are small arrows that must coordinate with the direction the water flows.

PRESSURE WASHER IS STARTING PLACE

Your PRESSURE WASHER FITTINGS orientation all starts with the inlet fitting on the pressure washer.  Most machines arrive with a socket as the initial set up.  So most machines have the water coming out with a “quick connect” or female coupler which is also called a socket.  If this is your initial set up, then everything else needs to be set up the same way.  I also refer to this as the “lead fitting.”  For my preferred set up, I remove that quick connect coupler or socket and replace it with a plug fitting.  This might also be called a male fitting.  I also demonstrate the change I make for my preference on a surface cleaner at the 6:30 time stamp.  There’s so much more to learn about this entire issue so be sure and watch the entire video!

ADDITIONAL TRAINING

Our next DIFFERENCE MAKERS CONFERENCE is coming up June 8-9 at Courtyard Marriott in Kingwood, Texas.  We are also looking at bringing the conference in Florida in the Fall of 2023.  I host monthly events featuring hands on training with classroom instruction.  For those not able to get to Houston, check out my online video school.

by Dean Dean

PRESSURE WASHER CONNECTIONS

PRESSURE WASHER CONNECTIONS

Thanks for checking out this PRESSURE WASHER CONNECTIONS video post.  The Doug Rucker Store is both online and also has a physical location.  We are in Porter, Texas where I often tell people: “It’s not the end if the world, but you can see it from here!”  If you are even in the Houston area, we hope you’ll stop by to talk some shop.  This video post is in response to questions about how to connect a pressure washer to the battery and the gas tank.  One of the most popular machines our customers seem to like is the 8 GPM cold water skid unit.  This machine does not come with a battery, battery cables, or a gas tank.

 

BATTERY CONNECTIONS

PRESSURE WASHER CONNECTIONS usually start off with a battery.  You will need a positive wire and a negative wire (red and black) with crimped fittings.  The fittings must properly fit the battery terminals as well as the starter on the machine.  The length of these wires must fit how far the location of the battery will be from the machine.  It should be pretty precise so that you are not short, nor do you end up with extra wire.  This is why custom builds are a key piece of our business and why Doug Rucker Store works so tirelessly with our customers on this.  At about the 2:00 time stamp with clear lighting and pictures, I help you identify the starter.  It can be difficult to locate.  I discuss the various options for grounding this connection.  Apply some sort of grease to each of those connections. I also discuss various battery sizes that you can use.

GAS TANK CONNECTIONS

PRESSURE WASHER CONNECTIONS are not complete until the gas tank is also in place.  I use 1/4 inch clear braid hose for the fuel line connection.  This hose is clear enough that it allows you to see the gas flow.  You could also use standard black fuel line if you prefer for other reasons.  You could install a Y fitting to supply a second machine such as our KINGSLINGER SOFT WASH SYSTEM.  I also discuss oil changes so be sure and watch the entire video for all the details.  I hope this helps answer some questions you may have regarding pressure washer connections.

 

 

by Dean Dean

TRUCK SKID

TRUCK SKID

This is a basic TRUCK SKID system video that explores each piece of equipment available at The Doug Rucker Store.  This particular type of set up is extremely popular and we have built many of these in the past.  Keep in mind all of the rig builds are completely customizable.  You design your own set up, and we’ll build it for you.  But this TRUCK SKID unit is a great template to consider for your pressure washing business.  It is a compact system built on a pallet skid that can be moved with a fork lift.  You can move this from truck, trailer or van and then into storage if necessary.  They are adaptable to you particular space, equipment and transport needs.

SKID EQUIPMENT BREAKDOWN

This TRUCK SKID starts out with a cold water 8 GPM skid pressure washer.  There is a 14 gallon fuel tank, which will allows you to complete an entire day’s work without running out of fuel.  The FLOW PRO down stream remote system is also on board.  The video clearly shows how the bypass mounts between the pressure washer and the Flow Pro remote box.  The three way poly valve allows easily switching from mix to water.  This enables him to rinse out his downstream injector.  Keep in mind that the owner for this particular TRUCK SKID set up will be using it for downstreaming only.

HOSE REELS

There are two 12 inch King’s reels with a 200 foot fierce jet pressure hose and 100 foot of flexilla garden hose.  And finally, there is a 55 gallon water tank which supplies the pressure washer.  Some may suggest that this is too small of a tank.  However, if you are solely providing residential service, the water tank is continually filling.  At the same time, you are on and off the gun so using the water is somewhat sporadic.  This tank also has the Topaz float valve inside.  Don’t hesitate to leave a comment if you have any questions.  We always enjoy an opportunity to build a custom truck, trailer or van rig that you design.

by Doug Rucker Doug Rucker

WINTER SEASON EQUIPMENT MAINTENANCE

WINTER SEASON EQUIPMENT MAINTENANCE

This WINTER SEASON EQUIPMENT MAINTENANCE video post will be helpful to pressure washing professionals during our slower season.  There are several tips you can be doing to prepare for the busy season to avoid frustration on the job and increase your productivity.  And we hope all of our posts and videos help small businesses grow by expanding skills and saving time, money and effort.  We’re thankful for our students that we provide lifelong mentoring to as well as our loyal YouTube channel viewers.  Thanks for watching this WINTER SEASON EQUIPMENT MAINTENANCE video and be sure to give us a like and leave a comment!

CHANGE JROD NOZZLES WINTER SEASON

One of the first things I do is go through all my JRODs and change all my nozzles.  I always do this annually at the beginning of busy season.  We have brass and stainless steal nozzles, and I predominately use brass nozzles for soft washing.  Brass is a less expensive option and lasts about the same as stainless steal.  This is due to the bleach continually running through them.  I do use stainless steal for high pressure work.  As a reminder, we use the KINGSLINGER soft wash system for all vertical surface cleaning jobs.  So check out the 1:50 time stamp of this WINTER SEASON EQUIPMENT MAINTENANCE video.  This is where I explain how I actually use a three nozzle set up.  It eliminates the rinse high nozzle.

REPLACE ALL O RINGS WINTER SEASON

You will need to make sure you have a good dental pick set or something similar for this WINTER SEASON EQUIPMENT MAINTENANCE item.  You also will need bags of O Rings in both 1/4 inch and 3/8 inch.  From the top of your pressure washing gun going forward, everything is 1/4 inch.  This includes the ends of things like nozzles, wands, lances and so forth.  From the bottom of the gun going in reverse, everything is 3/8 inch.  This applies to things like the machine, hose reels and everything moving toward your equipment.  At the 5:30 time stamp, I demonstrate precisely how to change O RINGS, what they look like, and the importance of seating each O RING properly.  There is a particular sound you can listen for that is most likely the result of an O RING that is bent, deformed, torn or has become unseated.  Allowing faulty O RINGS to continue functioning could result in damage to your equipment so it’s best to change them as part of your WINTER SEASON EQUIPMENT MAINTENANCE plan.

OTHER WINTER SEASON ISSUES

I go over what needs to happen with your downstream injectors and what we use to keep everything well lubricated.  It’s just so frustrating to get our there on your first spring job.  You’re all ready to make some money, but then your downstream injector won’t draw water.  You’ll want to make sure you have plenty of teflon tape and loxeal thread locker.  There is a pressure test gauge that will come in handy when you’re wondering whether you’ve lost pressure or flow volume.

by Doug Rucker Doug Rucker

Choosing Pressure Washing Equipment

Choosing Pressure Washing Equipment

As you begin to plan and build your pressure washing business, there are many challenging decisions.  So choosing pressure washing equipment that is best for your business is a one of those important decisions.   One of the questions you will hear most often is what is your business model going to be?  Likewise, the questioner is trying to determine what type of business are you going after.  Residential and Commercial cleaning can be two different types of cleaning, requiring different types of equipment.  Notice I said can be? They can also be very similar, and can be done the with the same exact equipment.

Choosing Pressure Washing Equipment

Choosing Pressure Washing Equipment

One of the things I like to do in our school is provide assistance when you are choosing pressure washing equipment. Especially when selecting equipment for the type of work you plan to do.  This is why the Doug Rucker Store is now open for pressure washing business equipment and supplies.  With over thirty years of experience in this business, We know exactly what you need for your business to succeed.  And we never try to over sell you or sell you items you do not need.  If you only intend to clean houses, not roofs, there is no need for a dedicated pump.  Soft Washing vinyl siding, stucco, eifs, and even brick houses come clean with a pressure washer and the correct nozzles. The only time a dedicated pump would be needed is if you are planning to clean roofs.

Dedicated Pumps

Dedicated pumps that are powered by a 12V battery or even some air diaphragm pumps are really best suited for cleaning roofs, and the occasional small house or building.  If you are planning to get into large upscale homes and commercial buildings, then choosing pressure washing equipment that has a high volume pump, like 5-10 gpm, will enable you to clean much faster, making you more profitable.  These types of pumps allow you not only to get your detergents on a large surface faster, they will also provide much faster and more thorough rinsing.

Never buy Pressure Washing Equipment that will not make you profitable

I am more than happy to assist any student of my school with choosing pressure washing equipment that will best suit your business and your budget.  Usually after a short consultation, I can pin point your exact needs and then put together a package for your that will build your business. And we provide much needed support after the sale.

For more information on our schools and dates of events, please visit our web site , email us at pressurecleaningschool@gmail.com, or call or text me at 2818833630